Ositech comm Trumpcard Data/Fax Modem Manual do Utilizador descarregar pdf (Página 18)

2 - 2 Trumpcard 14400/28800 Modem

Section Two

Installing the Trumpcard Modem

The Trumpcard Modem can be inserted into a computer whether the power

is ON or OFF.

Follow these steps:

• Orient the Trumpcard Modem so that the 68-pin connector is next to

the PCMCIA slot of the computer.

• Insert the Trumpcard Modem into the slot until it is firmly seated.

Note: These are general installation instructions that apply to most

computers. Please refer to the manual accompanying your computer

for any additional instructions on installing PCMCIA PC Card adapters.

Note: The Trumpcard Modem is keyed to go in one way only. If you feel

resistance before the it is fully inserted, remove it, turn it over, and re-

insert it.

Installing the Trumpcard

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 85 86

Trumpcard Data/Fax Modem 1
User’s Guide and Reference 1
Copyright 2
How To Contact Us 2
Contents 8
Modem Command Reference 4-1 9
Modem Test Procedures 5-1 9
Introduction 11
Features 12
Facsimile Mode 13
Cellular Mode 13
Unique Features 14
Industry Standards 15
Section One 16
Hardware Installation 17
Preparing for Installation 17
Installing the Trumpcard 18
Section Two 20
Basic Modem Operation 21
Before You Begin 22
Operating the 23
Making an Outgoing Call 24
Re-Dialling the Last Number 25
Storing a Number 25
Connection Messages 25
Section Four 26
Ending Your Connection 27
Connection 27
Receiving an Incoming Call 28
Cellular Phone Configuration 30
Outgoing Cellular Call 30
Incoming Cellular Call 30
Cellular Call Status 31
Modem Command Reference 33
Modem Command Guidelines 34
Modem Command Summary 36
Modem Command Descriptions 38
Bn — Set ITU-T or Bell Mode 39
Dn — Dial 39
Examples 40
En — Command Echo 41
Sub-parameter Definitions 42
Hn — Switch-Hook Control 43
In — Identification 44
Ln — Speaker Volume 44
Mn — Speaker Control 44
Nn — Automode Detection 45
P — Set Pulse Dial as Default 46
Qn — Result Code Display 46
Sn — Read/Write S Registers 46
T — Set Tone Dial as Default 47
Vn — Result Code Form 47
Wn — Connect Message Control 47
Xn — Extended Result Codes 48
Section Four 50
Zn — Reset 51
&Cn — DCD Option 51
&Dn — DTR Option 52
&Gn — Set Guard Tone 53
&Ln — Line Type 54
&Mn — Communication Mode 54
&Qn — Communication Mode 54
&Rn — RTS/CTS Option 55
&Sn — DSR Option 55
&Tn — Test and Diagnostic 56
&Wn — Store User Profile 58
\Bn — Transmit Break 59
\Kn — Break Control 59
\Nn — Operation Mode Control 61
%Cn — Compression Control 61
-Kn — MNP Extended Services 63
*Hn — Link Negotiation Speed 63
:En — Compromise Equalizer 64
Modem S Registers 66
Modem Register Summary 66
Register Descriptions 69
S5 — Backspace Character 70
S11 — DTMF Tone Duration 71
S12 — Escape Code Guard Time 71
S18 — Test Timer 72
S24 — Sleep Inactivity Timer 72
S25 — Delay to DTR 72
S30 — Inactivity Timer 72
S32 — XON Character 73
S33 — XOFF Character 73
S36 — LAPM Failure Control 73
S46 — Protocol Selection 75
S48 — V.42 Negotiation Action 76
S95 — Extended Result Codes 77
Facsimile Commands 78
Modem Test Procedures 79
Local Modem Self-Test 80
Local Analog Loopback 81
Generated Pattern 82
Remote Digital Loopback 83
Local Digital Loopback 85
Testing Modem Memory 86

Comentários a estes Manuais

Sem comentários

Ositech comm Trumpcard Data/Fax Modem Manual do Utilizador Página 18

Comentários a estes Manuais